*
News: SMF - Just Installed!


Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

SMIA Tool Locked Out! 4344

Super Newbie Posts: 9 Karma: +0/-0 *
SMIA Tool Locked Out!
« on: September 20, 2013, 08:46:04 AM »
All,

We recently rebuilt our FSM and now our SMIA tool is locked out so I am unable to reconfigure the SAN fabric. Does anyone know how to reset this darn thing!?!

Thanks!
Administrator Sr. Member Posts: 309 Karma: +6/-0 *****
Re: SMIA Tool Locked Out!
« Reply #1 on: September 20, 2013, 08:49:08 AM »
Hello Brands1284,

Try this, we recently received this action plan from IBM Support as a workaround.

Happy FSMing!  ;)
=========================================================                                                                           
 To change the SMIA user ID and password, complete the                     
following steps:                                                           
                                                                           
1.  Open a management software CLI prompt and log in.                       
                                                                           
2.  Use the rmdatasource command to remove the switch from Storage         
    Control management, as shown in the following example.                 
    Note: This example does not show all of the possible options for the   
    rmdatasource command. For more information about the command, see       
    rmdatasource.                                                           
                                                                           
    smcli rmdatasource -t https -i <IP_address> -p <port_number>           
                                                                           
    where <IP_address> and <port_number> are the IP address and port of     
    the switch.                                                             
                                                                           
3.  Log in to the management software web interface.                       
                                                                           
4.  From the Home page, click the Applications tab.                         
                                                                           
5.  Under SMIA Configuration Tool, click Launch administration             
    console. The SMIA administration console window opens.                 
                                                                           
    Note:                                                                   
                                                                           
     a.  If this is the first time you launch the tool, you                 
         must download it before you can use it. If necessary, confirm     
         the browser security exceptions, and the application               
         downloads.                                                         
                                                                           
     b.  The SMIA Configuration Tool is a component                         
         of IBM? Network Advisor. The download progress window and         
         other interface elements might                                     
         be labeled as IBM Network Advisor, but the SMIA Configuration     
         Tool provides only a subset of full Network Advisor               
         functionality.                                                     
                                                                           
6. Log in to the console; then, use the console to change the               
   administrator user ID and password.                                     
                                                                           
   Important: If this is the first time you launch the tool, you must       
   change the default protocol setting from HTTP to HTTPS after you log     
   in. The IBM Flex System FC5022 16Gb SAN Switch supports only HTTP       
   Secure (HTTPS), but the default protocol for the SMIA Configuration     
   Tool is HTTP.                                                           
                                                                           
    Note: If you cannot log in to the SMIA Configuration Tool, see         
    Troubleshooting the SMIA Configuration Tool.                           
                                                                           
7.  From the management software CLI prompt, use the mkdatasource           
    command to reestablish management of the switch, as shown in the       
    following example.                                                     
                                                                           
    Note: This example does not show all of the possible options for the   
    mkdatasource command. For more information about the command, see       
    mkdatasource.                                                           
                                                                           
    smcli -user USERID -pw Passw0rd mkdatasource -c fabric -i               
    <IP_address> -t https -p 25989 -u USERID -w Passw0rd -n /interop       
                                                                           
    where <IP_address> is the IP address of the management node.           
    Note: Port 25989 is the default port number of the SMIA                 
    Configuration Tool.                                                     
Super Newbie Posts: 9 Karma: +0/-0 *
Re: SMIA Tool Locked Out!
« Reply #2 on: September 20, 2013, 09:02:24 AM »
This is not working. :/

USERID@gvicfsm:~> smcli rmdatasource -i 192.168.240.62 -c fabric -t https -p 443
Removing data source ...
DNZSAL236E : No CIMOM fabric data source was found in the IBM Flex System Manager Storage Control server. Verify that the IP address, protocol, and port are valid.


I think because since the rebuild of the FSM I could NEVER manage the switches then it makes sense why it cannot find the datasource using the CIMON protocol. This is why I needed access to the SMIA tool in the first place...
Administrator Sr. Member Posts: 309 Karma: +6/-0 *****
Re: SMIA Tool Locked Out!
« Reply #3 on: October 25, 2013, 03:25:58 PM »
After doing some searching we found that the default administrator password for the smia tool is
Administrator/password.
Super Newbie Posts: 1 Karma: +0/-0 *
Re: SMIA Tool Locked Out!
« Reply #4 on: March 11, 2016, 11:57:01 PM »
I have tried to sign in your account name Administrator/password but it is not ok.
And:
USERID@FSM-6CAE8B7C5EFA:~> smcli rmdatasource -c fabric -t https -i 10.50.127.104 -p 25989
Removing data source ...
DNZSAL236E : No CIMOM fabric data source was found in the IBM Flex System Manager Storage Control server. Verify that the IP address, protocol, and port are valid.

Thanks!
Super Newbie Posts: 1 Karma: +0/-0 *
Re: SMIA Tool Locked Out!
« Reply #5 on: July 05, 2017, 02:08:31 AM »
After doing some searching we found that the default administrator password for the smia tool is
Administrator/password.

Thanks man, that get me in.