Hello again and again)
after you help with fod key, recovery base media
Now all prepare stage complete and now need configuring other component in FSM

1. Trouble
need help with Ethernet Switch

Severity:    Unable to set Simple Network Management Protocol (SNMP) notification destination: Automatic configuration failed. To manually define SNMP settings, open System Configuration > Current Configuration and then edit the Protocol Configuration for the desired switch.Warning
Name:    
Unable to set Simple Network Management Protocol (SNMP) notification destination: Automatic configuration failed. To manually define SNMP settings, open System Configuration > Current Configuration and then edit the Protocol Configuration for the desired switch.      
Event Severity:    Warning

USERID@FSM:~> ping6  fd67:6020:10a2:0:aa97:dcff:fe88:36ef
PING fd67:6020:10a2:0:aa97:dcff:fe88:36ef(fd67:6020:10a2:0:aa97:dcff:fe88:36ef) 56 data bytes
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=1 ttl=63 time=1141 ms
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=2 ttl=63 time=142 ms
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=3 ttl=63 time=2.03 ms
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=4 ttl=63 time=1.02 ms
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=5 ttl=63 time=1.19 ms
64 bytes from fd67:6020:10a2:0:aa97:dcff:fe88:36ef: icmp_seq=6 ttl=63 time=1.50 ms

IPv6 Address fd67:6020:10a2:0:aa97:dcff:fe88:36ef
IPv4 Address 192.168.60.76
but in IBM FSM Explorer 192.168.70.120

but in FSM i see all ok

IPv6 Address fd67:6020:10a2:0:aa97:dcff:fe88:36ef
IPv4 Address 192.168.60.76

Warning

and i see only 1 switch ( mb stack ? )

go resolve warning

step-by-step

 To manually define SNMP settings, open System Configuration > Current Configuration and then edit the Protocol Configuration for the desired switch

very long w8ting "Working" when edit Protocol Configuration

offtop - very cool, if i can post picture then my text next picture and text, now all picture in bottom post, strong for understantding

and i see deffault account where problem?

mb need delete warning? this only cosmetic? cuz on EN4093R warning missing ( after full reinstalling FSM =)  )
but in FC5022 have this warning too

when i try change CurrentConfiguration in FC5022

how verify my modules SAN\ETH switch.... work properly or not ?

When i start collect inventory I\O Modules

December 8, 2014 11:47:22 AM MSK-Level:1-MEID:0--MSG: Job "Collect Inventory - December 8, 2014 11:47:18 AM MSK" activated.
December 8, 2014 11:47:22 AM MSK-Level:200-MEID:0--MSG: Subtask "Collect Inventory" activated.
December 8, 2014 11:47:22 AM MSK-Level:200-MEID:0--MSG: Starting clients
December 8, 2014 11:47:22 AM MSK-Level:100-MEID:0--MSG: Clients started for task "Collect Inventory"
December 8, 2014 11:47:22 AM MSK-Level:200-MEID:0--MSG: Subtask activation status changed to "Active".
December 8, 2014 11:47:22 AM MSK-Level:150-MEID:0--MSG: ATKSRV629I Collecting inventory by using inventory profile "All Inventory".
December 8, 2014 11:47:22 AM MSK-Level:150-MEID:72348--MSG: ATKSRV628I Collecting inventory for "x.x.x.77", which has a type of "Switch".
December 8, 2014 11:47:22 AM MSK-Level:150-MEID:72378--MSG: ATKSRV628I Collecting inventory for "x.x.x.76", which has a type of "Switch".
December 8, 2014 11:47:22 AM MSK-Level:150-MEID:72406--MSG: ATKSRV628I Collecting inventory for "x.x.x.78", which has a type of "Switch".
December 8, 2014 11:47:22 AM MSK-Level:150-MEID:72436--MSG: ATKSRV628I Collecting inventory for "x.x.x.79", which has a type of "Switch".
December 8, 2014 11:47:22 AM MSK-Level:1-MEID:0--MSG: Job activation status changed to "Active".
December 8, 2014 11:47:22 AM MSK-Level:200-MEID:0--MSG: Subtask activation status changed to "Active".
December 8, 2014 11:47:32 AM MSK-Level:150-MEID:72378--MSG: Need to unlock SNMP RemoteServiceAccessPoint for Switch fod inventory.

i am used adminmd5 for snmpv3 or adminsha not work ( |partial access" anyway

EN4093R staked

partial access on slave switch ( work ONLY SSH ) HTTPS or SNMP not work
on master all work fine

how need configure stacked switch in FSM? cuz inventory all time failed on RSAP ( SNMP )

Now only one trouble have now

1. EN4093R - Stacked, Slave switch have partial access, i think this is normal - throught slave switch must not change configuration for SWITCH only view

but when i started inventory IO modules, all time Job have error about RSAP ( SNMP access )

All other trouble disappeared, FC5022 work correcly now and other subsystems

question only about EN4093R ( Stacked ) stayed

Liks,

I would verify this with someone from IBM but I believe the Slave switch would no longer control some of the management layer protocols now that it is a subordinate to the Master switch. For example, you should not have GUI access to that Slave switch as everything should now be shown under the master switch. However, I'm not sure what happens in a stacked configuration when the Master dies? Does the Slave take over and assume all management roles like SNMP? It would be nice to have the ability to test this.

thoughts?

if master dies, slave become Master and stay "Master"
if Master recovery after fail he become Slave switch and stay in this state

if Restart Master or both switch after reocvery "failed switch"

Slave switch ( failed Master ) become Master and old Slave switch returns role "Backup"

it's work for switch

now i go testing how it's work in FSM =)

Solution

Prerequisite:
1. You have stacked switch
2. You have FSM
3. You have warrning "partial access" for one or few switch, if you have at least 2 switch in stack
4. MB this solution can help for other troubles cuz this is critical error

Go to resolve trouble

Case:
EN4093R
EN4093R
and this switchs in stacked mode

1. Step

Verifying switch

login via ssh on both switch

type this command on all switch

IBMBaldeNetwork#show stack switch
IBMBaldeNetwork-2#show stack switch

in bottom find line

Switch 1
Local switch:
    Switch Mode (cfg) - Master

Switch 2
Local switch:
    Switch Mode (cfg) - Master

Yes, this point where i have trouble
i have stacked switch but BOTH switch have ROLE MASTER

FSM verify this line and think BOTH switch can manage via all RSAP

but in stacked mode 1 switch can change configuration /cfg/ menu or conf t in iscli
2 switch only /information or #show in iscli  have

2. Step

how to resolve ?
go to switch where you !can't! conf t use
IBMBaldeNetwork-2#show stack switch
stack name: Liks
Local switch is the backup.

Local switch:
   csnum             -  2 <- this number remebmer

go to switch where you !can! use conf t

IBMBaldeNetwork#conf t
IBMBaldeNetwork(config)#stack backup 2


Now reload

after reload complete ->

verify Roles

IBMBaldeNetwork#sh stack switch
stack name: Liks
Local switch is the master.

Local switch:
   Switch Mode (cfg) - Master

IBMBaldeNetwork-2#show stack switch
stack name: Liks
Local switch is the backup.

Local switch:
   Switch Mode (cfg) - Member (backup)

yes, Eng not my native) but mb this help anybody

Now in FSM you see this

all work correctly
 

Very nice!!! Glad this worked out and thank you for the valuable information.

Thanks!!   

Your plugins are the best  I love using them, although a manual or tutorial on how to use them would REALLY help me out.

Nice website and great that you have a forum here now.

Mike